High-Quality J1939 to OBD II Connector Cable for Vehicles
Deutsch Green J1939 Male to OBD II SAE J1962 Female automotive cable assembly
- Voltage: DC 300V 5m ohm/10 ms
- Contact resistance: 3.0 ohm MAX
- 100% open, short, and mis-wire testing
SAE Standards Documentation
- J1708 - Defines serial communications between ECUs on heavy duty vehicles
- J1850 - Defines serial data protocol with VPW and PWM variants
- J1939 - Defines data protocol for heavy duty commercial vehicles
- J1962 - Defines physical connector for OBD-II interface
- J1978 - Defines minimal operating standards for OBD-II scan tools
- J1979 - Defines standards for diagnostic test modes
- J2012 - Defines trouble codes and definitions
- J2178-1 - Defines network message header formats
- J2178-2 - Provides data parameter definitions
- J2178-3 - Defines network message frame IDs
- J2178-4 - Defines network messages with three byte headers
- J2284-3 - Defines 500 kbit/s CAN Physical and Data link layer
- J2411 - Describes GMLAN protocol for newer GM vehicles
J1962 Connector Specifications
The SAE J1962 specification provides two standardized hardware interfaces: Type A and Type B. Both are female, 16-pin D-shaped connectors. Type A is used for 12V vehicles, while Type B is used for 24V vehicles and features blue marking.
| Pin Number | Description |
|---|
| 1 | Manufacturer Discretionary |
| 2 | SAE J1850 Bus + (VPW / PWM) |
| 3 | Manufacturer Discretionary |
| 4 | Chassis Ground |
| 5 | Signal Ground |
| 6 | CAN High (ISO 15765-4 and SAE J2284) |
| 7 | ISO 9141-2 / ISO 14230-4 K Line |
| 8 | Manufacturer Discretionary |
| 9 | Manufacturer Discretionary |
| 10 | SAE J1850 Bus - (PWM-only) |
| 11 | Manufacturer Discretionary |
| 12 | Manufacturer Discretionary |
| 13 | Manufacturer Discretionary |
| 14 | CAN Low (ISO 15765-4 and SAE J2284) |
| 15 | ISO 9141-2 / ISO 14230-4 L Line (Optional) |
| 16 | Vehicle Battery Power: Type A 12V/4A, Type B 24V/2A |
Material: PA66, tinned plated compliant ROHS
Working temperature: -20°C to 80°C
Over-molding: Customized
Pitch: 4mm
Voltage: 12V for cars and 24V for heavy vehicles
DEUTSCH HD10 Series Connector
The HD series is an environmentally sealed, thermoplastic cylindrical connector designed for heavy-duty applications in trucks, buses, cross-country vehicles, cranes, and forklifts. Provides protection from water, dust, oils, fuel, road salt, and other contaminants.
- Operating temperature: -40°C to +125°C
- Withstands 20 test cycles from -40°C to +125°C without cracking, chipping, or leaking
- No unlocking or unmating after sinusoidal vibration testing (20 G's at 10-2000Hz)
- IP68 rating - waterproof, withstands immersion under 1.2 meters of water for 24 hours
| Cavity | Overall Length A | Overall Height ØB | Overall Length C | Overall Height ØD |
|---|
| 3 | 1.609 (40.87) | 1.069 (27.15) | 1.639 (41.63) | 0.851 (21.62) |
| 4 | 1.639 (41.63) | 1.595 (40.51) | 1.639 (41.63) | 1.281 (32.54) |
| 5 | 1.609 (40.87) | 1.218 (30.94) | 1.639 (41.63) | 1.001 (25.43) |
| 6 | 1.619 (41.12) | 1.453 (36.91) | 1.639 (41.63) | 1.141 (28.98) |
| 9 | 1.609 (40.87) | 1.593 (40.47) | 1.639 (41.63) | 1.281 (32.54) |
HD10 Series Configuration
| Position | Contact Size | Rear Threads | Plug | Receptacle Inline | Receptacle Flange |
|---|
| 3 | 16 | no | HD16-3-16S | HD14-3-16P | - |
| 3 | 16 | yes | HD16-3-96S | HD14-3-96P | HD10-3-96P |
| 4 | 4/16 | yes | HD16-4-4S | - | HD10-4-4P |
| 5 | 16 | no | HD16-5-16S | HD14-5-16P | HD10-5-16P |
| 6 | 16 | yes | HD16-6-96S | HD14-6-96P | HD10-6-96P |
| 6 | 12 | yes | HD16-6-12S-B010 | HD14-6-12P | HD10-6-12P |
| 9 | 16 | no | HD16-9-16S | HD14-9-16P | HD10-9-16P |
| 9 | 16 | yes | HD16-9-96S | HD14-9-96P | HD10-9-96P |
| 9 (J1939) | 16 | yes | HD16-9-1939S | HD14-9-1939P | HD10-9-1939P |
Company Profile
- Privately held company, established in 1999
- Sales volume over 16 Million USD since 2017
- OEM & ODM company with 250+ employees
- 7,260 square-meter facility
- Specialized in economical solutions and innovative wire harness design & manufacturing
- IATF16949 (2016) & ISO 9001 (2015) certified
- UL certified supplier with wiring No. E468011 & cable No. E479323
Certifications
Frequently Asked Questions
Can you help with design?
Yes, we are an ODM/OEM company specializing in wire harness & cable assembly since 1999.
When will you start to help design?
We provide initial solutions for discussion. After quotation and order placement, we begin detailed design and confirmation with the client.
What if quality issues occur?
Our quality and engineering team responds to quality issues within 72 hours. We are committed to long-term partnerships and providing excellent service.
Do you have standard products to reduce lead time and tooling costs?
Yes, we have over 1000 sets of molds, some of which can be used directly for customer projects. With over 20 years of experience and 5000+ products.
